Self-Hosted Repair Blueprint
Knowledge Base Procedure
CC BY-NC-SA 4.0 Verified
Google Pixel 7 Battery Replacement
This repair guide was authored by the iFixit...
Difficulty: Moderate
Duration: 3600 mins
Steps: 18 Steps
Hardware: Google Pixel 7
Repairability: 6.5/10
Attribution: Community Contributor
Freebase Entity Facts & Knowledge Triples
Graph Node
Namespace: /diy/procedure
| Entity MID / Identifier | /diy/procedure/ifixit_154680 |
|---|---|
| RDF & Freebase Types | /type/topic /diy/procedure /domain/hardware_repair |
| Subject Hardware Entity | Google Pixel 7 (dev_google_pixel_7) • OEM: Google • Category: Smartphone • Repairability: 6.5/10 |
| Procedural Complexity | Rating: Moderate • Estimated Duration: 3600 minutes |
| Step Records & Execution Stages | 18 Ordered Step Records (/diy/step_record) with instruction text, warning levels, and CDN media |
| Topological Tool Dependencies | 13 Hardware Tools (/tool/hardware) |
| Required Replacement Parts | 2 Component Entities (/part/component) |
| Provenance & Attribution | Source: iFixit Open Library • Author: Community Contributor • License: CC BY-NC-SA 4.0 |
Required Hardware Tools (13)
/tool/hardware- Microfiber Cleaning Cloths (Repair Tool)
- T3 Torx Screwdriver (Repair Tool)
- iOpener (Repair Tool)
- Heat Gun (Repair Tool)
- Safety Glasses (Repair Tool)
- Suction Handle (Repair Tool)
- iFixit Adhesive Remover (Repair Tool)
- iFixit Opening Picks (Set of 6) (Repair Tool)
- Clampy - Anti-Clamp (Repair Tool)
- Spudger (Repair Tool)
- Isopropyl Alcohol (90% or Greater) (Repair Tool)
- Tweezers (Repair Tool)
- Thermal Paste (Repair Tool)
Replacement Components & Consumables (2)
/part/component- Google Pixel 7 Battery - Genuine (Replacement Part)
- Precut Double-Sided Adhesive Card (Replacement Part)
Step-by-Step Instructions (18 Steps)
Compound Value Type Disassembly Flow
1
CVT: /diy/step_record/1
Step 1
Apply a heated iOpener to the back of the device to loosen the adhesive underneath. Apply the iOpener for at least 3 minutes. A hair dryer, heat gun →, or hot plate may also be used, but be careful not to overheat the device. The edge should feel slightly too hot to the touch.
2
CVT: /diy/step_record/2
Step 2
Use tweezers, or your fingers, to peel the plastic pull tabs away from the battery.
3
CVT: /diy/step_record/3
Step 3
Pull the tabs back and forth in a sawing motion up the length of the battery to separate the adhesive underneath. Work slowly. It's easy to lose your grip and accidentally pull the tab up from under the battery. If you're having difficulty separating the adhesive, apply more heat and wait for the adhesive to loosen. If you lose or tear the release strip, follow the next step for an alternative battery removal method.
4
CVT: /diy/step_record/4
Step 4
Follow this step if you couldn't loosen the battery using the battery release strip. Apply a few drops of high concentration (90% or higher) isopropyl alcohol into the gap at the top edge of the battery. Don't apply too much alcohol, or you'll loosen the NFC antenna and charging coil underneath the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Use the flat end of a spudger or an opening pick to gently lift the top edge of the battery until you can grab it with your fingers. Don't use excessive force on the battery. Slow, consistent pressure is all that's required to free it from the frame. Take care not to puncture or bend the battery with your tool—a punctured or bent battery may leak dangerous chemicals or cause a fire.
5
CVT: /diy/step_record/5
Step 5
Tilt the battery out of the device to separate the rest of the adhesive. Remove the battery. Do not reinstall a damaged or deformed battery, as doing so is a potential safety hazard. To secure the replacement battery: Apply pre-cut adhesive adhesive → or double-sided tape to the battery well at the places where the old adhesive was located, not directly onto the battery. Temporarily reconnect the battery to the motherboard to help align it correctly. Disconnect the battery after it's seated. Make sure that the battery sits in the center of the battery well and there's an even gap around the battery. Press the new battery firmly into place.
6
CVT: /diy/step_record/6
Step 6
Apply a heated iOpener to the screen to loosen the adhesive underneath. Apply the iOpener for at least 3 minutes. A hair dryer, heat gun →, or hot plate may also be used, but be careful not to overheat the device. The edge should feel slightly too hot to the touch.
7
CVT: /diy/step_record/7
Step 7
Once the screen is warm to the touch, apply a suction handle to the bottom edge of the screen. If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen. Lift the screen including its safety frame with the suction handle to create a small gap between the screen and the phone assembly. Depending on the age of your phone, this may be difficult. If you're having trouble, apply more heat to the bottom edge and try again. Insert an opening pick into the gap.
8
CVT: /diy/step_record/8
Step 8
To avoid damaging your phone, don't insert your pick more than ~2.5 mm as you separate the screen adhesive. Note the following areas: The screen cable is a little less than halfway up the left edge of the phone. Be very careful here to avoid tearing the cable. There are many spring contacts around the perimeter of the phone. Be very careful in these areas to avoid bending the contacts.
9
CVT: /diy/step_record/9
Step 9
Slide the opening pick to the bottom right corner of the screen to slice its adhesive. Leave the opening pick in place to prevent the adhesive from resealing.
10
CVT: /diy/step_record/10
Step 10
Insert a second opening pick at the bottom edge and slide it to the bottom left corner of the screen to slice the adhesive. Leave the opening pick in place to prevent the adhesive from resealing.
11
CVT: /diy/step_record/11
Step 11
Insert a third opening pick underneath the bottom left corner of the screen. Slide the opening pick along the left edge of the screen to slice the adhesive and to release the plastic clips. Leave the opening pick in the top left corner to prevent the adhesive from resealing.
12
CVT: /diy/step_record/12
Step 12
If the adhesive becomes hard to cut, it has most likely cooled down. Use an iOpener or heat gun for 1-2 minutes to reheat it. When you slice near the front facing camera, insert only the tip of the opening pick (~2.5 mm) to avoid damaging or smearing the camera. Insert a fourth opening pick at the top left corner of the screen. Slide the opening pick along the top edge of the phone to slice the adhesive. Leave the opening pick in the top right corner to prevent the adhesive from resealing.
13
CVT: /diy/step_record/13
Step 13
Insert a fifth opening pick and slide it along the right edge of the phone to slice the remaining adhesive and release the right plastic clips. Do not try to remove the display all the way yet, the screen is still connected to the phone assembly by a flex cable.
14
CVT: /diy/step_record/14
Step 14
Lift the right edge of the screen up and towards the left side of the device, like opening a book. Don't twist the screen or move it too far away from the frame to avoid straining or damaging the flex cable. Rest the screen upside down and parallel to the frame before continuing.
15
CVT: /diy/step_record/15
Step 15
The display cable bracket sits tightly and requires some force to release it. Insert one arm of a pair of tweezers into the opening at the upper end of the display cable bracket. Push the bracket inwards and pry up to release it.
16
CVT: /diy/step_record/16
Step 16
Use a pair of tweezers to remove the display cable bracket by pulling it from underneath the midframe and in direction of the cameras.
17
CVT: /diy/step_record/17
Step 17
Use a spudger to disconnect the display flex cable by prying the connector straight up from its socket. To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.
18
CVT: /diy/step_record/18
Step 18: The back of the Pixel's screen is very fragile
The back of the Pixel's screen is very fragile. Even a small scratch or dent can damage the screen. To prevent damaging your screen or replacement screen: When handling your screen, grip it by its edges. When placing the screen on your work area, make sure nothing is touching the bottom of the screen. Consider placing it on a soft, lint-free cloth.
Open Knowledge Commons • Licensed under CC BY-NC-SA 4.0 •
Source: iFixit Open Library •
Curated & attributed to Community Contributor